Cherry Blossom Sideboard Part 3

Hello All,

Since I completed the side assemblies in part 2, I was now ready to cut some stopped dadoes ( grooves going across the grain) to hold the bottom and the middle shelves... and rabbets ( a long notch at the top edge of the side assembly) to hold the sub-top.

For this operation I used a hand held plunge router. Since accuracy is very important I had to come up with a way so that these dadoes and rabbets will line up precisely in both pieces. I simply ganged and clamped both sides together, so that I can set up a fence across the whole assembly to rout out perfectly alligned dadoes and rabbets (as seen in top photo).

With a little fine tuning the shelves and sub-top fit quite nicely. The last photo shows all the completed cuts in both corresponding sides. The next step will be to rout a rabbet along the back edges of the sides and top and bottom to receive the back. I will also cut some dadoes into the top and bottom pieces to receive the center gable or divider. Be sure to tune in next time for part 4!

Thanks for looking!

Roshaan

Cherry Blossom Sideboard Part 2

Hello Everyone,

Well, I am making some progress on this project. I just completed the side assemblies, which consists of the legs, the top and bottom rails and side panels. I used mortise and tenon joinery to attach the rails (the horizontal top and bottom parts) to the legs and I then went ahead and cut a 1/4" deep groove into the legs and rails to receive the side panels. Since the panels and the rails were both 3/4" thick I had to cut a rabbet (notch) along all the edges of the panels to fit into the 1/4" thick groove. This also adds a nice reveal on the outside of the assembly.

The series of photos shows the steps in the order that it was completed.

The top photo shows all the parts layed out exactly how it will eventually be

assembled and glued together. The second photo shows the detail of the joinery including the rabbet along the edges of the side panel. Below that we have a photo of the glue-up of all the parts. I use t-stands to elevate the assembly, for easy gluing and clamping. And voila!...we finally have the side assembly of the sideboard. I will eventually taper the legs after I have cut all the joinery on the inside face of the side assemblies.

It truly is a great feeling to see the outcome of a whole bunch of parts scattered on your bench! I am sure that most woodworkers will agree when I say that the glue-up is the most stressful part of any woodworking project.

But we all love the rush!

Roshaan

Cherry Blossom Sideboard - Part 1

Hi All,

As promised, I have been taking in-progress photos of the cherry blossom sideboard build to share with everyone. With any project, especially a large build, organization and preparation is key to the success of it's outcome.

I always start with a detailed drafted working drawing to work out any of the joinery, measurements and proportions before I even

touch a piece of wood. I then like to make a scale model of the piece

to see what the full sized piece would actually look like and to work out any issues with proportions.

After I am satisfied with the proportions of the piece I then go ahead and make a cutting list of materials, which will include the size of all parts, the type of wood to be used and the joinery to be used. I then take these measurements and physically "map-out" or layout each part on the appropriate piece of wood. For example if I use veneered sheet goods (a fancy name for plywood) as seen in the above photos, I use a large square and draw the size of the part with a pencil right on the sheet of plywood and I mark each part. This way I minimize waste.

Before I cut into solid wood, I also let the planks acclimatize to my workshop for at least 3 days to a week if possible. Notice the way I have the project lumber stacked up on my bench with scrap pieces of wood in between each layer. This is done so that the underside of the boards will also receive appropriate airflow.

I also make sure I have my working drawings and cutting list on hand at all times. This will avoid any confusion and waste of materials. And remember to always measure twice...or three...or four times and cut once!

Roshaan

Cherry Blossom Sideboard

Hello Everyone!

I am embarking on a new project and I am excited to give you an inside look at the progress. It is essentially a sideboard with two sliding doors and these sliding doors will have a cherry blossom motif scroll sawn into the panels. It also has a modern asian appeal, with tapered legs, beveled top and a "rising cloud" curved bottom rail. I have been asked to design and build this piece to hold piano books, which of course has a particular size which had to be considered. My client has been searching high and low for the right piece with no success. She finally contacted me to see if I could come up with a suitable design. After weeks of mulling over the details of the piece I have successfully come up with a design she was happy with. I will be posting in-progress photos, so please check back for updates.

Roshaan

Mokajade wood studio website

Hello All,

I have finally launched my new website. It is still a work in progress, but I am happy with the overall look of the site. The website is divided into categories by the function of each piece. For example the belt buckle seen on the right can be found under the "Personal" category. Also look out for the Home, Office, Wall and Furniture categories to find what you are looking for.

I will also be offering my scroll saw patterns for sale in the near future, so please check back periodically for updates. Not too much of a diyer? Let me do the work for you. Just send me an email with your custom request.

Please have a look at mokajadewoodstudio.com and thanks for looking!

Roshaan

One-on-one workshop with Lesley

Hello Everyone,

I had a great opportunity to teach a one-on-one woodworking workshop from my modest yet organized garage shop. This workshop was to be a birthday gift for the sister of a great friend of mine. Btw...what a great birthday gift idea! Please take note for future reference :)

Lesley was an ideal student since she had a great passion for anything handmade and she was willing to learn in a very short amount of time. I have to give her credit for sticking with me to the very end of a fun but exhausting 8 hour day. At the end of the day she went home with a great token of her hard work...a lovely keepsake box made out of hard maple with a cherry wood scroll sawn top.

I gave Lesley a few scroll saw patterns to choose from, and she immediately gravited to the elegant, yet intricate dragonfly design. The design was a bit ambitious for a beginner, but I told her she had to be happy with the design since she was planning to keep the box for a very long time. The box sides was mitered which was then further enhanced with cherry splines. Splines not only add strenth to the joint but also dresses up a simple mitered box. There are no visible hinges, because the lid opens with the aid of 1/8" diameter brass pivot pins which is glued with epoxy into drilled holes in the sides of the box.

At the end of the day Lesley was extremely pleased with what she accomplished in such a short amount of time and so was I. I hope she will enjoy the keepsake box for a very long time and will keep it in the family for many more years to come.


Roshaan

Simply Wood on Amazon

So, I googled my name the other night and ...come on... I know you all google your own name sometimes...you know who you are. I was pleasantly surprised to find my book on amazon! Of course it's not being released just yet. The release date is scheduled for November 2010. I just wanted to share the link with you. So here it is...Simply Wood!

Roshaan